TECHNICAL DATA SPC-31
GLITTER SPRAYS
Form: CS1893
Rev.: 012114
.DESCRIPTION AND USES .
Glitter Sprays are designed to provide a sparkle finish on
many surfaces including wood, metal, wicker, ceramic,
pottery, Styrofoam
®,
paper, plastic, and more. For added
protection, top coat with Rust-Oleum
®
Glitter Sealer. The
clear topcoat helps prevent Glitter from flaking and fading
while maintaining the sparkle finish. For use on interior
items only.
.PRODUCTS .
267689 Glitter Gold
267734 Glitter Silver
268045 Glitter Red
267736 Glitter Clear Sealer
276287 Glitter Bright Pink
277781 Glitter Kelly Green
278073 Multicolor Glitter Purple
.PAINTING CONDITIONS .
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50ºF (10ºC)
and 90ºF (32ºC) and humidity is below 65% to ensure
proper drying. Do not apply to surfaces that, when heated,
exceed 200°F (93°C). Avoid spraying in very windy and
dusty conditions. Cover surrounding area to protect from
spray mist.
.PRIMING .
Use of a Painter’s Touch
®
primer provides excellent
adhesion and hiding and is especially recommended for
bare wood and metal. A primer, however, is not
recommended for Styrofoam
®
and paper. The following
primers are recommended.
249086 Red Primer
249088 Gray Primer
249058 White Primer
.PRODUCT APPLICATION .
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical
contaminants by washing the surface with a commercial
detergent, or other suitable cleaning method. Rinse with
fresh water and allow to thoroughly dry. Remove loose
paint and rust with a wire brush or sandpaper. Lightly
sand glossy surfaces to create a surface profile.
WARNING! If you scrape, sand or remove old paint from
any surface, you may release lead paint dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;
ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH
approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT
STRIKE CAN. Contact Rust-Oleum. Shake often during
use. Hold can upright 12-14” from surface and spray in a
steady back-and-forth motion, slightly overlapping each
stroke. Keep the can the same distance from the surface.
Keep the can in motion while spraying. Apply two or
more light coats a few minutes apart. Do not use near
open flame.
DRY & RECOAT
Dry and recoat times are based on 70ºF and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
touch in 20 minutes, to handle in 1 hour, and fully dry in 24
hours. Recoat at anytime.
CLEAN-UP
When finished spraying, clear valve by turning can upside
down and pushing spray button for 5 seconds. Clean-up
wet paint with xylene or mineral spirits. Properly discard
empty container. Do not burn or place in home trash
compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object
into can valve opening.
* Styrofoam
®
is a trademark of the Dow Chemical
Company.
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels